Hardware Assembiles

October 26th 2014, Hannah Perner-Wilson

This post seeks to define the parts, materials and techniques for producing the following hardware…

Progress on Collaborator glove testing

October 25th 2014, Kelly Snook
PCB versions 1.0 and 1.1

Various members of the team are busy testing the gloves as the technologies and designs…

ArduIMU Code

September 27th 2014, Hannah Perner-Wilson

If you don’t plan on using the Glover software you can program the ArduIMU to…

Bend Sensor Resistance Ranges

September 5th 2014, Hannah Perner-Wilson
Gloves sensor placement

Measurements taken on left hand of MiMu NIME glove, once with (bad) polyester sensors and…

Carrier Board Error

September 4th 2014, Hannah Perner-Wilson
Gloves PCB In Eagle

OUTX numbers in reverse order!

August Gloves Docu

August 27th 2014, Hannah Perner-Wilson

Bend Sensor Assemblies New neoprene solution: Button Assemblies Carrier Boards Motor Boards LED Boards

Replacing Polyester for Polyimide Sensors

August 6th 2014, Hannah Perner-Wilson

Replacing all 16 Flexpoint polyester laminate bend sensors for polyimide laminate sensors.

Bend Sensors Longevity Tests

August 6th 2014, Hannah Perner-Wilson
IMG_3274

We seem to be experiencing a change in the bend sensor’s behavior over time –…

Ring Button

August 6th 2014, Hannah Perner-Wilson

Imogen says she prefers the larger button which has a housing of about 11.5 x…

Breakout Board for NIME

April 12th 2014, Hannah Perner-Wilson

Everything that needs to be done in time for NIME!!!

Pull-up Resistor Values

December 13th 2013, Hannah Perner-Wilson

Figuring out the best value pull-up resistor for both the flex sensors and the e-textile…

Prototype x-OSC Gloves Kit

September 11th 2013, Seb Madgwick
Prototype x-OSC Gloves Kit Parts

Prototype x-OSC Gloves Kit for team to use in development. It is a self-contained, pre-configured…

Prototype x-OSC Gloves Video

August 31st 2013, Seb Madgwick

“Mega-Gluvs” V1

August 9th 2013, Hannah Perner-Wilson

Documentation of maga-gloves creation with Rachel Freire!

xOSC Gloves

May 9th 2013, Hannah Perner-Wilson

A pair of gloves using a new i/o board called xOSC developed by Tom and…

PS Move Gloves

March 5th 2013, Hannah Perner-Wilson

An attempt to build a pair of gloves from hacking a PS move controller.

FTDI LatencyTimer Driver Settings for Mac

January 31st 2013, Tom Mitchell
Fixed The FTDI Latency On Macs

The default driver settings for v2.2.18 of the for the FTDI Mac serial driver produce…

Workshop Gloves

January 27th 2013, Hannah Perner-Wilson

Three pairs of ArduIMU gloves for the CTM workshop. One extra pair as backup.

Configuring The RN-42 Bluetooth Module

January 24th 2013, Seb Madgwick
RN-42 Connected to FTDI For Config

The RN-42 Bluetooth module default settings are compatible with our intended use but some alternative…

Communication Protocol

January 19th 2013, Seb Madgwick

Tom and I met at my house and cleaned up the commutation protocol implementation for…

ArduIMU Circuit

January 13th 2013, Hannah Perner-Wilson

Notes – 6 analog inputs, but two don”t have internal pull/up resistors! – 6 BS:…

Got the RGB LED working

January 12th 2013, Seb Madgwick
Cut Bluetooth DTR Line

Met Tom in my lab to make more progress on the ArduIMU gloves. While testing…

Four Bend Sensors Per Glove?

January 7th 2013, Seb Madgwick

The ArduIMU has six analogue inputs and we are currently intending to use six bend…

Getting quaternions out of the ArduIMU

January 5th 2013, Seb Madgwick
Spikes in Gyroscope Data

My goal today was to get the ArduIMU sending quaternions.  I couldn’t get the official…

My First Arduino Project

January 2nd 2013, Seb Madgwick
Pull-up resistors on ArduIMU

This is my first post my first post and the start of my first Arduino…

Wireless

December 20th 2012, Hannah Perner-Wilson

Bluetooth mate on top of ArduIMU: